Alinco DJ-S45 Manuel d'utilisateur

ALINCO, INC.UHF FM TRANSCEIVERDJ-S45 CQ/T/EInstruction ManualThank you for purchasing this ALINCO FM transceiver.This instruction manual contains impo

92-4 Battery Level Indicator•Battery consumption level may changedepending on the surrounding temperatureor the frequency of use.•Even if the battery

103. Control Functions3-1 Names and Operations of the Transceiver ControlsTop and Front ViewsNo.①②③④⑤⑥⑦⑧⑨NamePower/Volume DialMIC Con

11Side ViewsNo.⑩⑪⑫⑬⑭NameSMA Antenna ConnectorPTT (press to talk) keyMONI keyDC-INFunctionsUndetachable fixed type antenna.Install the

123-2 Key OperationsNo.①②③④⑤⑥NamePTTMONIF/SET▼/T SQLV/M / MW▲/RPTIndependent operationTransmits or completes the setting in the Settin

13No.①②③④⑤⑥NamePTTMONIF▼/T SQLV/M / MW▲/RPTPressed for a whileEnables transmission while holding.Activates the monitor operation while h

143-3 Display*Unexplained icons are not used on this transceiver.No.①②③④⑤⑥⑦⑧⑨⑩⑪⑫⑬⑭⑮⑯⑰⑱Name IndicationAppears when the F key is pr

154.Basic Operations44. Basic Operations4-1 Turning the Power ONRotate the dial clockwise.To turn the power OFF, rotate the dial counter-clockwise unt

164-3 Operating ModesThe has two operating modes; VFO and Memory.The has three operating modes; LPD (VFO), PMR andMemory.Switching among modesEvery

174-4-1 Frequency SettingWhen keys are pressed, the frequency increases and decreasesin tuning steps.Adjusting the Frequency in 1MHz Steps( only)Pres

184-6 Memory ModeThe Memory mode is used to call up on a previously programmedfrequency. This transceiver has 100 memory channels (0~99CH).4-6-1 Memor

1ContentsNOTICE / Compliance Information Statement ...3Before Operating the Transceiver ...51.

194-6-2 Selecting a Memory Channel1. Switch to the Memory mode by pressingthe V/M key. The memory channel No.appears on the display.The Memory mode is

204-6-4 Programmable Items to Memory ChannelThe following data can be stored in each memory channel.•Frequency•Offset Frequency•Shift Direction•Tone F

214-7-2 Monitor Function•While the MONI key is pressed, the squelch opens and noise is heardfrom the speaker regardless of the squelch setting. "

224-8-1 Switching of Transmission Output Level( only)Transmission power can be changed to HI/LO by pressing the keys while transmitting."LO"

235. Parameter Setting ModeIn the Setting mode, you can set various functions of the .5-1 Selectable ParametersPlease refer to "5-2 Selecting th

2400.600 Offset frequency settingITEM No. 0303 This function sets the width of the frequency shift (0-99.995MHz).bEP-on Beeper ON/OFFITEM No. 0404 01

25bS-on Battery saving ON/OFFITEM No. 0808 05 Select ON to save the battery consumption during the stand-by status.bEL-oF Bell ON/OFFITEM No. 0909 06

26SCAn-t Scan (timed/busy channel) switchingITEM No. 1212 09 Choose between timed scan (SCAn-t) and busy channel scan (SCAn-b).Refer to "6-1 Scan

27SHIFt Repeater shift direction setting ITEM No. 1705.000 Repeater offset frequency settingITEM No. 18tonE Repeater tone encoding ON/OFITEM No. 1988.

285-2 Selecting the Setting Mode1. Hold the F key down for 2 seconds.The display changes to indicate that theSetting mode is activated.2. Select a men

24-7 Receiving ...204-7-1 Adjusting Squelch Level ...

295.Parameter Setting Mode5

306.Advanced Operations66. Advanced Operations6-1 ScanningUse this function to automatically search for signals.When a signal is received, scanning pa

316.Advanced Operations66-1-1 LPD (VFO) ScanScans the entire band in the LPD (VFO) mode.1. Switch to the LPD (VFO) mode bypressing the V/M key. 2. Pre

326.Advanced Operations66-1-3 Memory ScanScans only the programmed memory channels.1. Switch to the Memory mode by pressingthe V/M key. 2. Press and h

336.Advanced Operations66-1-5 Tone ScanThis function helps you to find the tone frequency in case CTCSSsystem is used.1. Press and hold the keys for

346.Advanced Operations6Quick-Repeater-Access Operation1. Press the V/M key to activate the LPD(VFO) mode.2. Press the F key, then the key while the&

356.Advanced Operations66-4 Tone Call (Tone Burst)Use this function to call a partner by adding an audible tone to thetransmitting signal.The tone sig

367.Selective Communicating77. Selective CommunicatingWhen communicating with a specific station, tone squelch (CTCSS)function can be used. Tone sque

377.Selective Communicating74. Press the PTT key or the V/M key tocomplete the setting and return to theLPD (VFO) mode.When "T" is displayed

387.Selective Communicating77-2 PMR Tone Squelch ( only)1. Press the V/M key to activate the PMRmode.2. Press the F key, then the T SQL keywhile "

3NOTICE / Compliance Information StatementThis equipment has been tested and found to comply with the limitsfor a Class B digital device, pursuant to

398.Cloning / Packet Operation88. Cloning / Packet Operation8-1 CloningWhen using the cloning function, all setting information (includingmemory data)

408.Cloning / Packet Operation8Transmitting the Master Data1. Press and hold the MONI key and pressthe PTT key three times."CLONE" appears o

418.Cloning / Packet Operation8Receiving the Master Data1. "Ld ***" appears on the slave unit'sdisplay while the master data is beingtr

428.Cloning / Packet Operation88-2 Packet Operation( only)Packet operation is one of the data communication methods, which enablesdata transmission an

439.Maintenance and Reference99. Maintenance and Reference9-1 ResettingWhen you reset the transceiver, all settings are returned to the initialfactory

449.Maintenance and Reference99-2 OptionsEBP-60 Lithium Ion Battery PackEDC-138A Quick Battery Charger 120VacEDC-138E/uk Quick Battery Charger 240VacE

4510.Specifications1010. SpecificationsDJ-S45 CQS/CQL•Specifications may be changed without a preliminary announcementin connection with technical dev

4610.Specifications10DJ-S45 T/E•Specifications may be changed without a preliminary announcementin connection with technical development.Frequency Ran

ALINCO, INC.Head Office:Shin-Dai building 9th Floor2-6, 1-Chome, Dojimahama, Kita-ku, Osaka 530-0004, JAPANPhone:+81-6-4797-2136 Fax: +81-6-4797-2157E

4UHF FM Transceiver DJ-S45 TThis device complies with Part 15 of the FCC Rules. Operation issubject to the following two conditions: (1) This device m

5CautionThe use of transceiver in the following places is prohibited.•Aboard aircraft •In airports •In ports •Within or near theoperating area of busi

61. Functions and Features39 different Tone Squelch function (CTCSS)TOT (Time Out Timer) functionTone Call function (ALT, 1750, 2100, 1000, 1450Hz)Rec

72. Accessories2-1 Attaching and Detaching Accessories2-1-1 Antenna( only)1. Hold the antenna by its base and turn itclockwise until it stops.Check to

82-2 Setting Batteries1. Open the cover latch and then open thecover.2. Set two commercially available AAbatteries in the +/- orientation marked atthe