Alinco DJ-X7 Manuel d'utilisateur

DJ-X7T/EWIDE BAND COMMUNICATION RECEIVERTONEBANKSHIFTMWPRI10M/1MPWRBANDV/P/MSCANDJ-X7 WIDE BAND COMMUNICATION RECEIVERInstruction ManualALINCO, INC.

103Names and Functions of Parts3.1 External ViewChapter 3 Names and Functions of PartsEARPUSHVOL/SQLSETTONEBANKSHIFTMWPRI10M/1MPWRBANDV/P/MSCANDJ-X7

113Names and Functions of PartsFLOCKMONISKST891011 Side panel891011Antenna connectorFunction key (LOCK)Monitor key (ST/SK)DC-IN jackInstall the includ

123Names and Functions of Parts3.2 Key OperationsTONEBANKSHIFTMWPRI10M/1MPWRBANDV/P/MSCAN[F] keyDialV/P/MSCANBANDPWR10M/1MFDialSwitch among the VFO/Pr

133Names and Functions of Parts3.3 Icons and IndicatorsBlinks during various types of scanning operations.Disappears during the memory skip operation.

144Basic Operations4.1 Turning Power ONHold the key for 1second to turn the power ON.Hold the key again for 1second to turn the power OFF.4.2 Adjusti

154Basic Operations4.3 Adjusting Squelch Level"Squelch" is a function for eliminating noise which you may hearduring AM or FM radio receptio

164Basic Operations Mute functionThis is a mute function, and it's for cutting off the audio output.This is activated only when the [MONI] key is

174Basic Operations4.5 Frequency Settings VFO modeThis is the mode which is displayed when you turn the powerON of the receiver as a factory default s

184Basic Operations1. Press the key to select a band to change itstuning step.Note that the bands with the * marks in the lists shown at theprevious

194Basic Operations Memory mode1. Press the key to switch to the Memory mode.2. Press the key to select a bank you wish tomonitor.For more informati

2NOTICE / Compliance Information StatementThis device has been tested and found to comply with the limits for a Class B digital device, pursuant to pa

204Basic OperationsIt is not possible to program duplicated frequencies toa skip-search channel. If you try to do so, an errorbeep will sound. Program

21 Clearing memory channel1. Set the Write-protect function to OFF, if necessary.For more information, refer to "(14)Write-protect function setti

Chapter 5 Advanced Operations225Advanced Operations5.1 Scanning FunctionThis function automatically searches for active frequencies tohelp you locate

235Advanced Operations Programmed scanThis programmed scan searches for signals between aspecified range of frequencies. Both the higher and the lower

245Advanced Operations• The all banks scan is valid only for numeric banks,and other banks such as priority are disregarded.• The banks can be expande

255Advanced Operations4. Press the [MONI] key.You can now set the memory channel to be skipped. Thedecimal point (.) on the LCD goes off during the sk

265Advanced Operations3. Press the key.This starts the Descrambling function. The icon on the LCDblinks during the operation. Also, the decode No. f

275Advanced Operations5.7 Tone Scan FunctionThis function detects a CTCSS tone frequency of the receivingsignal automatically.1. In the VFO mode, rota

Chapter 6 Set Mode Configurations286Set Mode ConfigurationsYou can configure values or parameters of the DJ-X7's variousoperating functions in th

296Set Mode Configurations6.3 Set Mode ConfigurationsDetails of each item of the Set mode menu are as follows.(1)Attenuator function settingUse this f

3Precautions ...5Precautionary Statement ...

306Set Mode Configurations2. Rotate the dial to change the display as shown belowand select the antenna.When using the earphone antenna, a signal may

316Set Mode Configurations2. Rotate the dial to select the mode as you desire.The default is set to 5 seconds. The battery consumes fasterwhen you sel

326Set Mode Configurations2. Rotate the dial to switch ON/OFF of the function.Unless you set it to OFF, select the setting time.When you set it to ON,

336Set Mode Configurations2. Rotate the dial to switch ON/OFF of the function.When you set it to ON, the icon appears on the LCD.When the DJ-X7 recei

346Set Mode Configurations(14)Write-protect function settingThis is a memory-save function. This function preventsoverwriting or deleting memory chann

357Cable-clone and PC ConnectionCable-clone is a useful function for transferring the storedmemories and operating parameters from one receiver (calle

367Cable-clone and PC Connection7.3 Operation for Transferring Data (on the Master)1. Hold the key for 1 second to turn the power ONwhile holding the

378Maintenance and ReferenceChapter 8 Maintenance and Reference8.1 TroubleshootingPlease check the list below before concluding that the receiver is f

388Maintenance and Reference8.2 ResettingThe resetting deletes all programmed memory channels andreturns to the initial (default) factory settings.1.

398.4 Table of Available CTCSS TonesThe table below illustrates the available CTCSS tones.Rotate the dial while a tone frequency is displayed on the L

4(14)Write-protect function setting...34(15)Modulation Type setting ...34Chapter 7

409SpecificationsChapter 9 SpecificationsAMFM/WFMBattery contactsExternal DC portAverageStand-byBattery-save ONNFM/AMWFM1st2nd3rdFMWFMAMNFM/AMWFM0.100

ALINCO, INC.

5PrecautionsPrecautionary Statement• Do not open the case nor touch the interior components.Tampering can damage the receiver.• Do not place the recei

• DJ-X7 is a wide band receiver and can be applied tobusiness use.• DJ-X7 receives AM radio with the internal bar-antenna.• DJ-X7 receives high freque

72.1 Mounting Arrangement Installing & uninstalling antenna●Installing antenna1.Hold the antenna at the base.2.Attach the antenna to theantenna co

Caution• Do not modify, dismantle, incinerate, or immerse thebattery pack, as these practices can be dangerous.• Do not short-circuit the terminals of

92Accessories Receiving while charging with AC adapter●Charging battery1.Install the battery pack to thereceiver.2.Plug the AC adapter to theDC-IN jac