Alinco DJ-460T Manuel d'utilisateur télécharger pdf

KB2LJJ Radio Mods Database

KB2LJJ

Home Radio Mods Database and Manuals

Modifications for the Alinco DJ-160

The new Alinco DJ-160 Radio will receive between 137-174 Mhz, and transmit in the 2Meter band only (144-148Mhz). A

simple modification to the radio will enable it to transmit in the full range it receives currently. I have not tested the output

power on other frequencies (Due to my one and only watt meter getting fried) however I have tried setting a weather receiver a

small distance away, and I did hear the radio in the receiver. To make the mod,

the following must be done: (I assume that you have some experience with electronics and that you can tell a wire from a

resistor, from a transistor)

1) Take the battery of the radio by lifting the battery release button. If you look at the bottom of the radio, there will be

a metal plate that is held on with 4 small screws. Take this plate off, noting exactly how the clip was held on (like the slot for

the battery release clip)

2) On the back of the radio there are two screws that hold the back of the radio on, take these screws out.

3) Now you should be able to lift the bottom part of the radio by the battery release button slightly apart. I was told that you

should take the top knobs off, but I found that I didn't have to.

4) If you take the Battery Release Button and turn it about 90 degrees, the button should come out easily. After you get the

small piece of plastic that is the button, you should see a yellow wire behind where the clip was.

5) Take a small wire cutter and CUT this YELLOW wire. You should probably make sure that the wire doesn't have bare metal

showing from a lousy cutter, because I don't think that grounding this wire

to the case would be HEALTHY for your radio. :-)

6) After You cut this wire. Assemble the radio, and just before you turn on the radio, do a power reset by holding the FUNC

button while turning on the radio. This will reset the radio to ALL of the factory set parameters. YOU WILL LOOSE

PROGRAMMED FREQUENCIES that were programmed into the memory mode of the radio, so just write the frequencies

down before proceeding with the above instructions.

7) The radio should be just like new, except that the transmit will be enabled for ALL frequencies! GOOD Luck!

If you use these mods for ILLEGAL purposes, pity upon thy sole, for you do not belong in the ranks of Amateur Radio. This

information is only supplied for Legal and Informational Purposes only and I can NOT be held responsible for anything that

you do with this INFO. And if you screw up your radio, TOO BAD. I can't be

held responsible.

Note: I haven't tried or verified this, proceed at your own risk.

Do not do this mod unless you have a legal and good reason, like being in MARS, or to drive a transverter.

Do not transmit outside of legal bands. I don't have any info beyond what is above, sorry.

DJ-160.TNC

Being new to packet, I had a hard time figuring out how to connect my. Alinco DJ160 HT to my TNC. Like many HT's Alinco

http://www.kb2ljj.com/data/alinco/dj-160.htm (1 di 10)20/08/2009 16.29.22



www.r6-ru4montesecchieta.it

IZ5CCV

1 2 3 4 5 6 7 8 9 10

Résumé du contenu

Page 1 - DJ-160.TNC

KB2LJJ Radio Mods Database KB2LJJ Home Radio Mods Datab

Page 2

KB2LJJ Radio Mods Database Item Adjustment Point Adjustment Method Spec1. VCO P/D voltage adjustmentL106 (VCO) Adjust L106 so that P/D voltage is 2.0

Page 3

KB2LJJ Radio Mods Databasehas no documentation on packet hook ups. After experimenting I finally was able to get the connection to work. Buck Rogers

Page 4

KB2LJJ Radio Mods Database (c) Marty Goodman February 1992The manual for the Alinco DJ160T is remarkably badly written, and certain functions in part

Page 5

KB2LJJ Radio Mods DatabaseTransmit: Radio transmits the tones 1,2,3 whenever [PTT] is pressed.(you must hold down the PTT button throughout your trans

Page 6

KB2LJJ Radio Mods Databasecode is received (1,2,3,4,*,7) the radio will make the personal page type beeping and "GP" will flash. In addition

Page 7 - DJ160 DTMF Decode

KB2LJJ Radio Mods Databasehear a personal page type beep, and "GP" will flash, but "Err" will be on the main display indicating th

Page 8

KB2LJJ Radio Mods Database DJ160 DTMF Decode I received your message about the DTMF decoding on the DJ-160, and I thought I should tell you that

Page 9

KB2LJJ Radio Mods DatabaseThis is the second step. If you modify all steps, frequency range will be: RX 108-142.995MHzTX&RX 130-173.995MHzRX 850-9

Page 10 - KB2LJJ Radio Mods Database

KB2LJJ Radio Mods Database1. VCO P/D voltage adjustmentL106 (VCO) Adjust L106 so that P/D voltage is 2.0 V at 146.03 MHz. (DC voltmeter) in the transm